煤矿锚杆机除尘马达改进

针对煤矿进口锚杆机除尘马达频繁出现故障的情况,通过排查除尘装置的安装方式和监测马达工作时的压力状态,查找故障原因,并制定解决方案。通过马达外接单向阀,可满足马达进油口最低安全压力限制的要求,解决了马达频繁损坏的问题,保障了设备工作的稳定性,提高了工作效率。     

Analysis and proposition of limiting current density measurement protocol

Limiting current density at different temperatures, backpressures, and balance gases can be used to separate molecular diffusion resistance, Knudsen diffusion resistance and local transport resistance of membrane electrode assembly (MEA). However, the measurement of limiting current density has no unified protocol. The diverse choices in the literature, either in the control of current or voltage or in the atmosphere like relative humidity and O₂ concentrations, make it difficult to compare the results and identify the true bottleneck hindering the mass transport. In this work, the current-voltage curves obtained by current scanning/stepping and voltage scanning/stepping methods under dilute O₂ of different concentrations and a wide range of relative humidity were measured and analyzed systematically. It is found that the voltage stepping method is superior to the other three ways of control for the reliable determination of the limiting current density. Aided with simultaneous electrochemical impedance spectroscopy measurement, the limiting current density can be determined with pinpoint accuracy. When the limiting current density is just used to qualitatively evaluate different MEA, the voltage scanning method can be used instead for its high time efficiency. The selection of the atmosphere also plays an important role in suppressing the distortion from excessive water and reducing the spurious contribution from proton conduction resistance. It is found that O₂ concentrations at 0.5 vol% and relative humidity at 90% can give the best estimation of O₂ transport resistance in membrane electrode assembly.     

基于参数预标定的长行程PMLSM无传感器控制

为了解决长行程定子不连续永磁直线同步电机存在的因无法全程安装位置传感器和不同动子和定子之间的电磁参数不固定所造成的控制性能下降的难题,提出一种在每一段定子内先进行参数标定,再进行速度控制的控制系统设计。首先,在动子进入过程中,对电机进行电磁参数标定,根据标定参数对控制器参数进行调整,以达到更好的控制效果。然后,使用无位置传感器控制系统使动子快速达到设定速度值并稳定运行。实验结果表明:动子进入过程参数标定精度分别为0.002Wb和0.000 4H;无位置传感器控制中位置估计精度为0.63mm,速度收敛时间为0.45s,稳态误差为0.02m/s。基本满足永磁直线同步电机用于长行程运输的控制快速性、稳定性等要求。     

基于电信号特征分析的电机故障诊断技术

介绍了电机故障诊断技术平台的组成,分析了电机常见故障下电信号的特征。利用宜昌和景洪工厂两台电机进行了实际对比测试,宜昌工厂电机定子电流特征频率在49.2Hz时表现出峰值-36.08dB,在50.8Hz时表现峰值则为-37.23dB,表明电机存在转子断条故障;景洪工厂电机在转子特征频率为113.51Hz时,出现峰值-58.47dB,表明电机存在静态偏心故障。经电机现场抽芯检查,验证了电机故障快速诊断平台给出的电机健康状态评估结果,证实了基于电信号特征分析的电机故障诊断技术的准确性。     

基于时频域的卷积神经网络运动想象脑电信号识别方法

针对目前运动想象脑电（EEG）信号识别率较低的问题，考虑到脑电信号蕴含着丰富的时频信息，提出一种基于时频域的卷积神经网络（CNN）运动想象脑电信号识别方法。首先，利用短时傅里叶变换（STFT）对脑电信号的相关频带进行预处理，并将多个电极的时频图组合构造出一种二维时频图；然后，针对二维时频图的时频特性，通过一维卷积的方法设计了一种新颖的CNN结构；最后，通过支持向量机（SVM）对CNN提取的特征进行分类。基于BCI数据集的实验结果表明，所提方法的平均识别率为86.5%，优于其他传统运动想象脑电信号识别方法；同时将该方法应用在智能轮椅上，验证了其有效性。     

新型卡板式外径千分表的设计应用

针对机车牵引电机转轴磨削测量中,对转轴轴承位尺寸超差的原因进行分析,设计制作机车牵引电机转轴新型卡板式外径千分表(实用新型:ZL201420477030.7)。实际应用表明,新型卡板式外径千分表保证了牵引电机转轴轴承位的磨削尺寸,避免了转轴轴承位尺寸超差现象,解决了机车牵引电机转轴轴承位磨削测量的工艺、质量问题。     

开关磁阻直线电机的设计及其推力优化

设计了一种开关磁阻直线电机,使用JMAG软件对其进行了仿真和优化。进行了推力公式的推导,研究了导通顺序和初始位置对电机推力的影响,并分析了三种典型情况的磁力线分布。对电机的定子和动子的齿部和轭部高度、宽度及铁耗进行仿真优化,得出了最优参数。将有取向硅钢应用于该电机,研究了推力与轧制角的关系,并与使用普通硅钢的开关磁阻直线电机进行了对比,推力有一定提升。提出在动子齿部开切向槽的方案,结果表明,开切向槽对推力的影响较小,并能显著减小推力波动。     

Robust SVM-direct torque control of induction motor based on sliding mode controller and sliding mode observer

This paper proposes a design of control and estimation strategy for induction motor based on the variable structure approach. It describes a coupling of sliding mode direct torque control (DTC) with sliding mode flux and speed observer. This algorithm uses direct torque control basics and the sliding mode approach. A robust electromagnetic torque and flux controllers are designed to overcome the conventional SVM-DTC drawbacks and to ensure fast response and full reference tracking with desired dynamic behavior and low ripple level. The sliding mode controller is used to generate reference voltages in stationary frame and give them to the controlled motor after modulation by a space vector modulation (SVM) inverter. The second aim of this paper is to design a sliding mode speed/flux observer which can improve the control performances by using a sensorless algorithm to get an accurate estimation, and consequently, increase the reliability of the system and decrease the cost of using sensors. The effectiveness of the whole composed control algorithm is investigated in different robustness tests with simulation using Matlab/Simulink and verified by real time experimental implementation based on dS pace 1104 board.     

Combined constant speed control method for a wind generator equipped with hydraulic energy storage

A wind generator equipped with hydraulic energy storage (WG‐HES) uses hydraulic transmission systems instead of gearbox transmissions, thus eliminating high‐power converters and reducing the tower‐top cabin weight. When there is no wind or the wind speed is extremely low, the pressured oil released by accumulators is used to drive a motor to operate at a constant speed, thereby generating constant‐frequency power. However, few studies have examined the constant speed control characteristics for generating electricity using only an accumulator group. In this study, a combined constant speed (CCS) proportional–integral–derivative (PID) control method based on “variable displacement and throttling” is proposed, which includes two closed loops and one regulating loop. First, a simulation model of the CCS PID control method for a variable motor was established in the Simcenter Amesim program. The influence of different PID parameters on the anti‐interference ability of the constant speed control of the motor was analyzed under a given load step. Then, we obtained the range of control parameter values and a set of optimal values. Second, the effectiveness of the CCS control method and the accuracy of the simulation results were verified on a 600‐kW WG‐HES system prototype. The results verified that the CCS control method has good anti‐interference ability and can meet the requirements of constant speed control for a variable motor under the best PID parameters. These results can provide a basis for developing control strategies for WG‐HESs when there is no wind or at low wind speeds.     

用于嵌入系统的超声电机驱动设计

为了在嵌入式控制系统中充分利用超声电机特有功能,对超声电机的驱动原理进行了研究,在分析了超声电机的驱动控制原理的基础上,提出了一种基于单片机控制超声电机的软硬件控制实现方法。利用单片机输出数字量作为控制信号,通过串行输入并行输出芯片扩展后,输出到超声电机驱动器,实现超声电机启动/停止/正反转的功能;通过扩展单片机数模转换,将单片机控制超声电机速度的数字信号转换为电压信号,实现超声电机的速度控制功能;利用运行脉冲宽度控制实现超声电机的位置控制功能,并将光电编码器实现超声电机的反馈,最后通过试验验证了单片机系统实现超声电机驱动设计。